Ruger Mark II

This is a discussion on Ruger Mark II within the Rimfire forums, part of the Other Firearms category; A friend called me on Wednesday and wanted to make the rounds, so off we went. At a local Lawmenís, there she was. Sitting on ...

Thread: Ruger Mark II

Results 1 to 3 of 3
  1. #1 Ruger Mark II 
    Super Member Bgoff689's Avatar
    Join Date
    Nov 2009
    Location
    Irmo, South Carolina
    Posts
    3,197
    Ruger Mark II-rugermarkiixxdr-redu.jpg

    A friend called me on Wednesday and wanted to make the rounds, so off we went.

    At a local Lawmenís, there she was. Sitting on the bottom shelf at the far right was a familiar silhouette. Iíd recognize those Bolt Ears, those grips and that long tapered barrel anywhere.

    It was a Ruger Mark II Standard, with a 6 inch barrel, She in great shape and had been well kept. About 90% worth of kept. Standard sights and all metal, except for the grips. . The trigger was smooth, sort of like it had been tuned. The magazine was an M10 Standard. Not a scratch on her. Apparently sheíd been shot and put away dirty but, thatís an easy fix.

    Iíd been looking for one of these for quite awhile. I had one back in 1989, but Ex-Wife #2 had sold it while I was out of the country. Iíd inherited it from my Dad and as a teenager had put loads of ammunition through it. Since this one is packing SN 224ó82XXX mine must have been a Standard or Mark I.

    Ruger Mark II-rugermarkiil-redu.jpg

    Ruger produced this one in 2002. Strange enough the year that Bill Ruger died. Ruger started production of the Mark II in 1982 and stopped selling them in 2005.

    So, I finally got my Mark II. Iím planning a range trip this week. Unfortunately she only came with one magazine and thereís none available locally. Iíll just have to be patient. At $240.00 it was a good price.

    Ruger Mark II-markiidisassembled2-redu.jpg

    I disassembled and cleaned the weapon Thursday. Mark IIs are a bit easier that the Mark III 22/45s, but still loads of fun. Read the Ownerís Instructions for disassembly. Thatís the easy part.

    Reassembly is another manner. Iíve done the Mark I, II and III. Read the instructions and look around on YouTube. Itís one of those things best learned by doing. A few suggested tools.

    To remove the grip covers, I use a Brownells Magna Tip, with a 270-3 bit. Theyíre hollow and ground just right; it makes a perfect fit into the screw slot to avoid stripping it. I also use a 16 oz Strike Pro Fiberglass hammer, a plastic punch, a large paper clip and a couple of smaller gunsmith hammers.

    For reassembly, the barrel receiver goes on top of the frame so that the square lug engages the square front recess under the underside of the receiver. The barrel is pushed rearward until it stops, with the rear end of the receiver slightly over-hanging at the rear end of the grip frame.

    Thatís where the problems can start. If the mainspring housing bolt stop assembly pin doesnít protrude far enough above the top of the receiver, the pin will not allow the latch to close. After repeated effort if the pin doesnít protrude enough to allow the bolt stop assembly to latch in place, donít try to force it.

    Point the pistol barrel down and look behind the rear sight. Check the position of the Slide Bolt and see how it is seated into the receiver. The ears on the bolt have circular grooves. With the bolt inserted in the barrel, if the end of the receiver is not centered on these grooves, that means the barrel needs to be further back on the frame.

    Hammer time. Take the bolt out and reseat the barrel. With the bolt back in, the bolt stop assembly should slide right in and close the latch.

    Thursday we were out making the rounds and I ran into two Ruger Mark IIs at a decent price. But I'd already found mine. Strange how that works?
    I don't carry a weapon and look for trouble, I carry one in case trouble finds me.
    Reply With Quote  
     

  2. #2 Re: Ruger Mark II 
    Super Member RogueLCP's Avatar
    Join Date
    Oct 2009
    Location
    Southern Oregon
    Posts
    6,323
    Boy, you just keep adding to your collection. And we get to enjoy learning about them. Always enjoy you posts.
    Reply With Quote  
     

  3. #3 Re: Ruger Mark II 
    Suz
    Suz is offline
    Newbie Suz's Avatar
    Join Date
    May 2013
    Location
    Northeast, USA
    Posts
    9
    Good for you, but I am jealous! Had a pair of MKII's back in the 80's and have recently decided to try and find one again.
    Reply With Quote  
     

Home | Forum | Active Topics | What's New
Ads
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. New Ruger Mark III 22/45
    By alduane in forum General Firearm Discussion
    Replies: 15
    Last Post: 09-07-2012, 07:53 PM
  2. Working the Ruger 22/45 Mark III
    By Bgoff689 in forum Semi Autos
    Replies: 16
    Last Post: 02-23-2012, 02:35 AM
  3. Ruger Mark III
    By Tileman in forum Semi Autos
    Replies: 9
    Last Post: 04-09-2010, 01:28 PM
  4. Ruger Mark III 22/45 RP
    By MoHawk in forum Semi Autos
    Replies: 0
    Last Post: 01-20-2010, 03:47 PM
  5. Ruger Mark III sights
    By Puppybreath in forum Semi Autos
    Replies: 13
    Last Post: 08-20-2009, 09:43 PM
Search tags for this page
1951 ruger standard mark 1
,

how to peen ruger mark 2 receiver lug

,
mk ii ruger
,
removing ruger mark iii barrel from receiver
,

ruger mark 2 forum

,
ruger mark 2 prices
,

ruger mark ii

,
ruger mark ii bolt fits mark i
,
will ruger rimfire mark i barrel fit markii